Each induction cooking zone is distinguished by at least two concentric circles. The inner circle indicates the recommended minimum diameter of a specific utensil base. However, provided the utensil base covers approximately sixtypercent of the inner circle’s area, cooking will initiate. Anything less will not be recognised by the induction coil and no power is supplied. Utensil bases larger than the inner circle are recognised and the appropriate power requirement is adjusted automatically.
As an alternative to the traditional topmounting of a cookktop onto a benchtop, consider flushmounting into a benchtop. Topmounting is when the cooktop sits into a precut cavity with the entire cooktop’s surface sitting a few millimetres above the surrounding benchtop surface. Flushmounting uses the same precut cavity but with a rebated edging to allow the perimeter of the cooktop to ‘sink’ to a flush height with the surrounding benchtop. This type of installation is applicable to stone benches, such as marble and granite and the quartz resin benchtops.
Very rapid heating and boiling is possible within the two power boost zones — front left and the large 290mm diameter centre-right zone. This 290mm diameter zone is permanently rated to power boost of 3200 watts on level 9. The front 210mm diameter zone can go from 2300 watt to 3200 watt power boost by ‘borrowing’ power from the rearleft zone.
Ultimate safety is assured within each induction zone —
factory programming that each zone cooks no longer than 90 minutes continuously; residual heat warning LED of zones at or above 30° Celsius on the ceramic surface — a very visual ‘H’ LED flashes; boilovers or the weight of a utensil accidentally shifted onto the touch controls automatically shuts the induction heating system down and a constant acoustic signal sounds until human intervention simply turns the cooktop off.
finish: black ceramic surface, bevelled edging
installation: built-in hob
capacity three zones —
290mm diameter 3200 watt
160mm diameter 1400/1800 watt power boost
210mm diameter 2300 watt/3200 power boost
safety maximum operating timers
delay stop timers 99 minute maximum
LEDs plus acoustic acknowledgment
residual heat LEDs
thermal overload protection
Thermostat: nine heat settings per zone
Pan size: automatic electronic recognition
Warranty: two years parts and labour
net weight 11.87 kg
gross weight 13 kg
electricity supply 240 volt 50 Hz
electricity connection hard-wired single phase
maximum current 28.5 amp
maximum wattage 6800 watts
A: 1290mm diameter 3200 watt
B: 160mm diameter 1400-1800 watt
C: 210mm diameter 2300-3200 watt
cutout 560mmW x 490mmD
packaged dimensions: 120x610x670mm = 0.05m³
size 600mmW x 510mmD x 65mmH (60mm H benchtop displacement)
Home Clearance uses the Appliances Online delivery network, which services most major Australian cities. This means that we use our own fleet of trucks for deliveries – maintaining an exceptional standard of service every step of the way.
We offer 2 delivery options:
We offer free delivery to most major Australian cities – please use our delivery calculator or call 1300 002 500 to see if your suburb qualifies.
Please note that ‘free delivery’ means that we will bring the product into your house, but will not unpack or connect.
For a small fee of $39.95 we can unpack the product, remove any rubbish, and connect the new appliance to existing power and/or plumbing (excludes integrated fridge / freezers, wall-mounted dryers, hot water systems, air-conditioners, cooking appliances, audio & visual products and dishwashers). We can also remove your old appliance, if required.
Premium delivery is available in most major Australian cities – please use our delivery calculator or call 1300 002 500 to see if your suburb qualifies.
When you make an order, a member of our customer support team will contact you within 90 working minutes to provide an estimated time of delivery. Items that are in stock (in your state) are usually delivered the next business day.
The day before your item is due to be delivered, you will receive a text message confirming the delivery date. We will then give you a call on the morning of delivery to provide a 2 hour delivery window – and call again 30 minutes on approach.
You can let us know what your preference for a delivery time is, and we’ll do our best to accommodate you where possible. Please contact us on: 1300 002 500 for more information.
We offer Saturday premium deliveries to the Sydney metro area for a small fee of $39.95. Please contact us on: 1300 002 500 to find out if your suburb is eligible.
Yes, we can arrange for your new appliance to be installed by Handy Crew – our own team of fully licensed and accredited tradespeople. The advantage of using Handy Crew for your appliance installation is that you can rest assured you’re getting the best possible customer service and value for money.
For more information, please call us on 1300 002 500 or visit our Appliance Installation page.
All of our products come with full warranties from the manufacturer. This means you can enjoy all the benefits of buying a brand new item – except at a clearance price!
The warranty period will vary from 1 to 5 years, depending on the manufacturer.
We have a 7 day DOA (dead on arrival) policy, which means that you are entitled to a full refund or exchange if the product is mechanically defective within the first 7 days of purchase (confirmed by the manufacturer).
The Appliances Online Customer Experience Team is dedicated to helping you with any after sales requests. If your new purchase ever needs any technical attention during the warranty period, all you need to do is give us a call and we will take care of the rest.
Customer Care Plans are available for all products. Care Plans are only available at the time of purchase. If you have purchased a Care Plan, we will pay for the parts, labour and service fees (where applicable) if your product suffers a mechanical or electrical failure subject to the terms and conditions set out in our Customer Care Plan brochure.
A separate Customer Care Plan must be purchased for each product that you buy from us. Your tax invoice will specify the period of cover. Your Customer Care Plan starts at the expiration of the manufacturer’s warranty for your product.
To make a warranty claim, please contact the relevant manufacturer directly, or contact our Customer Service Liaison team on (02) 9694 0210. You will need your tax invoice when making a claim.
To make a claim under our Care Plan, please call the Care Plan Team on: 1300 100 824.
Enter your details below and we will review and respond to your query within 90 working minutes.